Waterproof Cap Ring Case with Silica Gel
Waterproof case for one set of 8-shot toy cap rings (up to 6 rings, 48 shots) for the RAGE grenade. TPU seal, a spindle filled with silica gel and an eyelet for a carabiner. Hang it on your vest and keep your caps dry and at hand.
| Category: | Accessories |
|---|
StrikeForge cap case – dry caps after a whole day in the rain
A small waterproof case for one set of RAGE grenade cap rings. Hang it on your vest and your caps are always at hand.
How it works
- Turn the case lid-down and unscrew the body. About 1.5 turns is enough.
- Slide the cap rings onto the spindle in the lid. It takes up to 6 rings – 48 shots.
- Fit the body and screw it on by hand until it stops. The TPU seal closes the case.
- When reloading the grenade, just slide the rings off the spindle – nothing spills out.
48 shots in a case that fits in your palm
Moisture stays out
- A TPU seal sits in the lid groove and presses against the rim of the body when tightened. It keeps rain, sweat and wet grass away from your caps.
- Silica gel inside the spindle absorbs the moisture that gets in when you open the case. The spindle comes pre-filled.
- The spindle has a left-hand thread. Opening the case tightens it, so it never works loose.
As tough as the RAGE grenade
The body, lid and spindle are made of ASA, which handles sun, frost and drops without turning brittle like ordinary plastics. A solid eyelet on the body takes a carabiner or key ring, so you can hang the case on your vest, belt, backpack or keys.
What's in the box
- 1× cap case (body, lid, TPU seal, spindle filled with silica gel)
Cap rings and carabiner are not included.
Specifications
| Model | SF-CC6 |
| Type | Waterproof case for 8-shot toy cap rings |
| Capacity | 1 set – up to 6 rings (48 shots) |
| Dimensions | Ø 35.4 × 30.7 mm, 47 mm including eyelet |
| Inner space | Ø 25 × 25.5 mm |
| Materials | ASA (body, lid, spindle), TPU 95A (seal) |
| Weight | approx. 21 g |
| Closure | thread, approx. 1.5 turns, hand-tight only |
| Drying | spindle with silica gel (pre-filled) |
| Mounting | Ø 6 mm eyelet for a carabiner or key ring |
| Designed and made in | 🇨🇿 Czech Republic |
Instructions for use
Before first use
- Check that the sealing ring sits flat in the lid groove all the way round.
- The spindle is screwed onto the lid. If it is not, hold the lid upside down and screw the spindle onto the pin anticlockwise (left-hand thread) until it seats. Hand-tight only.
Loading the caps
- Turn the lid upside down so the spindle points up.
- Slide up to 6 cap rings onto the spindle.
- Lower the body over the caps and screw it clockwise until it stops (about 1.5 turns). Hand-tight only, no tools.
Taking the caps out
Unscrew the body anticlockwise. Slide the rings off the spindle or tap them out of the body.
Silica gel
- The silica gel gradually absorbs moisture. From time to time, or when it changes colour, unscrew the spindle clockwise and empty out the beads.
- Dry the beads as instructed by the silica gel manufacturer, or replace them with new ones (3–5 mm). Pour them back in through the threaded opening and screw the spindle back on.
- Do not put the spindle or any other part of the case in an oven.
Care and sealing
- With the body fully tightened, the case protects the caps from rain, sweat and moisture. It is not designed for diving or prolonged immersion in water.
- Keep the sealing ring and the top edge of the body clean. Sand and dirt reduce sealing.
- Replace a damaged or deformed sealing ring.
- Wash with lukewarm water, not in a dishwasher. Do not expose to temperatures above 80 °C.
⚠️ Warning
- Not a toy. Not suitable for children under 14. Contains small parts – choking hazard.
- For storing 8-shot toy cap rings only. Do not store other pyrotechnic articles, ammunition, matches or batteries.
- When the case contains caps, keep it away from fire, heat sources, direct sunlight and impacts. Do not open near an open flame.
- Contains silica gel – do not eat. Keep out of the reach of children.
- Follow the cap manufacturer's instructions.
- Plastic parts (ASA, TPU) go to sorted plastic waste. Dispose of caps as instructed by their manufacturer.
Manufacturer: René Mahdal – StrikeForge, Modřínová 1414, 252 42 Jesenice, Czech Republic · info@strikeforge.eu · strikeforge.eu
Type: SF-CC6
Discussion
Be the first who will post an article to this item!